Chevy S10 Pickup Radiator

Vehicle is somehow like a human body since it is made up of different systems that perform detailed functions for the vehicle to work competently. Therefore, the absence of one part can make your vehicle useless. One of those very important parts of the vehicle is the radiator. The Chevrolet S10 radiator is the part of the cooling system that works by removing excess heat from the engine. Because the engine works harder compared to any other part, it has a big propensity to overheat; consequently, it needs a cooling system that would keep it operating at the correct level of temperature.

On normal basis, the temperature of the engine is about 2,000 degrees F. Throughout the combustion process, the engine will then create a huge amount of heat, which is approximately twice as much as its temperature is at regular condition. This is where the work of the cooling system comes in the picture, it will then remove at least one-third of that heat that take place in the combustion chamber so that the engine won’t overheat. Basically, the radiator is the device in the cooling system that works to dispel heat sucked up by the anti-freeze or coolant mixture from the engine. It is made up of tubes that is able to hold huge amount of water and passages that offers large area in contact with the air outside the vehicle.

Moreover, radiator also contains either vertical- or horizontal-finned tubing section that are affixed to the receiving tank as well as to the dispensing tank. There are also the side flow radiators that contain end caps on the side thus allowing lower hood line. Primarily, water is mixed with antifreeze will then move around the engine by means of the cylinder block and head. After which, they will absorb the heat from the engine as well as its parts. Next, the coolant will then be pumped from the engine down to the receiving tank above the radiator. It will spreads over the tops of the tubes. After being cooled in the radiator, it went back to the engine in order to suck up heat again and the cooling process continues for as long as the engine never to stop.

Damages to the radiator are normal. You can opt for a repair if the problem is not serious enough to seek for a replacement. But if it is, you can get your new Chevrolet S10 radiator here at our site. Parts Train is among the leading store for auto parts and components.

Featured Products

Radiator - Plastic End Tanks

RADIATOR -- 26.25 in. x 15 in. x 1.37 in. core size, 1.31 in. inlet size, 1.56 in. outlet size, 2-1/2 in. x 16-5/8 in. top header, 2-1/2 in. x 16-5/8 in. bottom header, plastic tanks, top left inlet location, bottom right outlet location; A high quality, direct fit OE replacement radiator; Covered by a 1-year unlimited mileage warranty.

Brand: Replacement
Material: Plastic End Tanks

Radiator - Aluminum Core, Plastic Endtanks

RADIATOR, 2-ROW -- 23.62 in. x 15 in. x 1 in. core size, 1.31 in. inlet size, 1.56 in. outlet size, 2-3/8 in. x 16-1/2 in. top header, 2-3/8 in. x 16-1/2 in. bottom header, plastic tanks, top right inlet location, bottom left outlet location; A high quality, direct fit OE replacement radiator; Covered by a 1-year unlimited mileage warranty.

Brand: Replacement
Material: Aluminum Core, Plastic Endtanks

Radiator - Plastic End Tanks

RADIATOR, 1-ROW -- 26.25 in. x 15 in. x 1.37 in. core size, 1.31 in. inlet size, 1.56 in. outlet size, 2-1/2 in. x 16-5/8 in. top header, 2-1/2 in. x 16-5/8 in. bottom header, plastic tanks, top left inlet location, bottom right outlet location; A high quality, direct fit OE replacement radiator; Covered by a 1-year unlimited mileage warranty.

Brand: Replacement
Material: Plastic End Tanks

Radiator - Aluminum Core, Plastic Endtanks

RADIATOR, 3-ROW -- 28.25 in. x 17 in. x 1.87 in. core size, 1.31 in. inlet size, 1.56 in. outlet size, 2-3/4 in. x 18-5/8 in. top header, 2-3/4 in. x 18-5/8 in. bottom header, soler on core, top left inlet location, bottom right outlet location; With transmission oil cooler; Without engine oil cooler; A high quality, direct fit OE replacement radiator; Covered by a 1-year unlimited mileage warranty.

Brand: Replacement
Material: Aluminum Core, Plastic Endtanks

Radiator

RADIATOR, 3-ROW -- 17.37 in. x 25.25 in. x 1.87 in. core size, 1.75 in. inlet size, 1.75 in. outlet size, 3 in. x 25-1/2 in. top header, 2-3/4 in. x 25-1/2 in. bottom header, soler on core, top left inlet location, bottom right outlet location; A high quality, direct fit OE replacement radiator; Covered by a 1-year unlimited mileage warranty.

Brand: Replacement