Pontiac Fan Blade
Get the right Pontiac Fan Blade from Partstrain! Select your vehicle to ensure that you will find the right parts with a perfect fit.
|
“An automobile’s efficient cooling system is dependent upon the radiator’s water and capacity, and the fan’s ability to pull air through the radiator and dissipate the heat,” an expert says. This is why even if your vehicle’s radiator is in perfect condition yet the fan cannot draw sufficient air to cool the hot water circulating through the radiator then it would still be inutile. Thus if you are planning to go for an upgraded radiator, it follows that you should also go for larger, or additional auxiliary electric fans or mechanical flex fans, to prevent overheating problems. Otherwise, the upgraded radiator tends to lessen airflow into the engine compartment, and there will be cool air deficiency that will take care of the system’s rising temperature.
However, there are instances when the cooling fans encounter problems of its own such as a defective fan blade. Some worn out fan blades result to a poor performance when pulling air, or sometimes unexpectedly breaks up or bends, or in very rare cases, melts down due to extreme heat pressure. Fan blades like the Pontiac fan blade is a fan component that is designed to project at an angle from the central hub, tasked to draw large volume of air through the radiator, and to cause some direct cooling of the engine by the created flow if air. Fan blades are powered by the fan motor, and are regulated by the fan clutch. A fan clutch is a viscous fluid drive coupling device attached to the center of the fan to allow variable engine fan speeds in relation to engine speeds.
Further, fan blades are driven by a fan or an electric motor. Fans driven by a fan belt is called an engine-powered fan. It is fastened to the water pump hub and pulley. However, when there is a gap between the fan and the pulley, a spacer is employed to move the fan closer to the radiator. They are spaced at intervals around the fan hub to help in controlling vibration and noise. Also, it is usually curled at the tip to augment its ability to draw air. Beside the differences in the placing of these blades around the hub, most of them have the same pitch and angularity for standard quality.
If upon checking your car’s cooling system you observe some noise, vibration and excess wear on the water pump shaft then the fan blades are probably having trouble. Have it replaced as soon as possible. You can get exceptional replacement fan blades here at Parts Train. We offer wide array of automotive parts and accessories including fan blades. Check it out now!
 Featured Products |
Fan Blade
FLEXALITE 1300 SERIES FLEX FAN BLADE, NATURAL FINISH -- 19.312 in. Fan Blade Diameter, Made Of Premium Quality Stainless Steel, Red Hub Made Of Steel Material, Belt-Driven, With 10,000 RPM Rating, Designed To Deliver Maximum Airflow At Low RPM, And The Least Amount Of Engine Loading At High RPM, Provides Less Resistance At Highway Speeds To Deliver More Horsepower And Better Gas Mileage, Must Be Used With A Fan Shroud, Clutch Not Required, With Flexalite's Limited 1-Year Warranty
|
Fan Blade
FLEXALITE 400 SERIES NYLON FAN, BLACK -- 17 in. diameter, 2 in. width, 6 blades, flex blade type, clockwise rotation, 800 RPM rating; Ideal for race and performance applications when cost or weight is a concern; Designed to be inexpensive and light; Provides maximum cooling and relieves stress on the water pump and bearings; Features a one-piece molded nylon construction and standard automotive mounting pattern; Must be used with a fan shroud; With Flexalite's limited 1-year warranty.
|
Fan Blade
FLEXALITE OE REPLACEMENT FAN -- Standard-Duty Thermal, 19 1/4 in. Diameter, 2 3/16 in. Projected Width, 4,000 Fan RPM Rating, Belt Driven, Made Of Premium Grade Steel Star With Painted Aluminum Blades, Designed As An OE Replacement Clutch Fan For Standard Duty Clutches Only, Must Be Used With A Fan Shroud, With Flexalite's Limited 1-Year Warranty
|
Fan Blade
FLEXALITE 5700 SERIES CLUTCH FAN, BLACK -- Standard-Duty Thermal, 18 in. Fan, With 4,000 RPM Rating, Belt Driven, Made Of Premium Grade Steel With Painted Aluminum Blades, Designed As An OE Replacement Clutch Fan For Standard Duty Clutches Only, Must Be Used With A Fan Shroud, With Flexalite's Limited 1-Year Warranty
|
Fan Blade
FLEXALITE 1300 SERIES FLEX FAN BLADE, RED -- 18-1/4" Fan Blade Diameter, Made Of Premium Quality Stainless Steel, Belt-Driven, With 10,000 RPM Rating, Designed To Deliver Maximum Airflow At Low RPM, And The Least Amount Of Engine Loading At High RPM, Provides Less Resistance At Highway Speeds To Deliver More Horsepower And Better Gas Mileage, Must Be Used With A Fan Shroud, With Flex-A-Lite's Limited 1-Year Warranty
|
|
|
